MIPI CSI Init Error
Forums: USB - Known Problems and SolutionsWe have designed our own cypress CX3 board to interface with our camera sensor. The design is based on E-Con CX3 Denebola development kit.We are getting error...
View ArticleUSB-IF Test Suite
Forums: USB - Known Problems and SolutionsHi,As part of custom firmware development on FX3, I would like to perform validation of my implementation. I have found the USB-IF Test Suite.I had a question...
View ArticleClik here to view.
FX3 Device descriptor failed
Forums: USB - Known Problems and SolutionsHi, I'm using a fx3 and when I connect my board to the pc I have the following error in the device manager : Unkown USB Device (Device Descriptor Request...
View ArticleInterfacing Xilinx Virtex-5 FPGA with CYUSB003 kit
Forums: USB - Known Problems and SolutionsHi,I am designing a custom board using Xilinx Virtex-5 FPGA and CYUSB003 kit as a piggyback module. I want both the Virtex-5 board and the superspeed kit to...
View ArticleFX3 - DMA Override mode and ZLP
Forums: USB - Known Problems and SolutionsHi,Testing communication between a WinUSB Host Application and the FX3, I am confronted to max packet length and zero length packet handling.On the host...
View ArticleClik here to view.
Debugging a ThreadX stack fault on FX3
Forums: USB - Known Problems and SolutionsI'm getting a "5 _tx_thread_stack_error_handler() 0x40030f44" in my application, under load (while doing something). I can't find anything on how to debug...
View ArticleHow to handle the getinterface() and setinterface() request from the host to...
Forums: USB - Known Problems and SolutionsHi,I am working in a project which requires switching into various alternate settings which are belong to the same interface. While searching about the...
View Articleezusb.sys
Forums: USB - Known Problems and SolutionsCan the driver named ezusb.sys be used on win7 64 os?Thanks in advance!
View ArticleCyUSB3.sys Device not started 0x25 CM_PROB_FAILED_DRIVER_ENTRY on Windows 7...
Forums: USB - Known Problems and SolutionsHi all,few days ago have got a problem with our customized CyUSB3.sys driver - on PC with fresh Windows 7 and no updates installed our driver failed to start...
View ArticleFX3 USB3.0 not working?
Forums: USB - Known Problems and SolutionsI have been having trouble with the SuperSpeed FX3 SDK board, and I am thinking that it might have to do with the setup/USB3.0 driver. Right now, the device...
View ArticleFX3 driver problem on Windows Embedded 7
Forums: USB - Known Problems and SolutionsDear Cypress Team, We use "CYUSB3014-BZXI"(FX3).We have developed our product base on the "AN84868 Configuring an FPGA over USB Using Cypress EZ-USB FX3"with...
View ArticleCYUSB3KIT-003 to SD card interconnect
Forums: USB - Known Problems and SolutionsHi,Can I connect an SD card to CYUSB3KIT-003 Header pins? Thanks
View ArticleClik here to view.
example code - The Hex file does not match the acquired device
Forums: USB - Known Problems and SolutionsHi Cypress guys,I am using miniProg3 to program CYPD2122-20FNXIT. when I use "PSoC Programmer 3.25.0.2504", every thing is OK. But when I run sample code...
View ArticleCCG4-Dead Battery Case : How is Chip powered ?
Forums: USB - Known Problems and SolutionsHello Everybody, I have a system using the CCG4.In dead-battery mode, Rd is detected via the CC-Line and VBUS gives 5V on the line.But How does the chip get...
View ArticleHow to improve the GPIO Frequency？
Forums: USB - Known Problems and SolutionsDear all，Now I want to use two gpios(as clock and data) to transfer a Bit-Stream.I tested the gpio clock frequency is 1.7MHz with using write register mode to...
View Articleconfiguration a spartan 3 with FX2LP in C++
Forums: USB - Known Problems and Solutionshi, i want to configure a spartan 3 with Cypress FX2LP. it is a App.note :...
View Articleanyone tried use cypress device with multiple threads?
Forums: USB - Known Problems and SolutionsHi, i am using cypress api with multiple threads.i have tried those threads one by one.they can individually work perfectly. the problem is, i could not run...
View ArticleMOBL-USB CY7C68053's startup
Forums: USB - Known Problems and Solutions As you know, CY7C68053 cannot enumerate without an EEPROM. CY7C68053 will read the EEPROM's first bytes' through I2C controller....which is called 'C2...
View ArticleUSB-to-UART bridge stopped working after new Windows 10 update
Forums: USB - Known Problems and SolutionsNeither a usb cable plugged into the pioneer board or a cy8ckit-049-42xx board plugged directly into the usb port will connect. I get usb power to the...
View ArticleCyUSB3.sys Device not started 0x25 CM_PROB_FAILED_DRIVER_ENTRY on Windows 7...
Forums: USB - Known Problems and SolutionsHi all,few days ago have got a problem with our customized CyUSB3.sys driver - on PC with fresh Windows 7 and no updates installed our driver failed to start...
View Article